DoorKing 1802 Bedienungshandbuch PDF herunterladen (Seite 2)

120 Glasgow Avenue

Inglewood, California 90301

U.S.A.

RING

CLCK

SENSE

SPK

VOL

FEEDBACK

MIC VOL

OFF

KEYPAD

321

MASTER

CODE

TONE

OFF

TONE

NC C

CONTRAST

DOORKING 1862-010

16AC16ACBATNONCCCOMSPKRMICMICGPSWCGNDPHONE

1810-075

sn XX

THIS SIDE UP

0000010100010

Door ControlGate Control

Main Terminal

Door Locks

Gate Operator

Power for electric strike or magnetic

lock is NOT provided by the system.

Use separate UL listed power supply.

Magnetic lock is wired to

the Normally Closed (NC)

relay input 1.

Electric strike is wired

to Normally Open (NO)

relay input 1.

Gate Operator

is wired to

Normally Open

(NO) relay

input 1.

Lock Power

UL listed

To Relay Input 1

Door

Lock

Wiring MUST be twisted and

completely isolated from ground.

Phone Line

Central Office

Phone Line Input

touch tone, loop start

Earth Ground

1802 MUST be Properly Grounded!

Relay Input 1

“NO” - Normally Open (NO)

“NC” - Normally Closed (NC)

“C” - Common (C)

Power Input

16.5 VDC, 20 VA power.

Wire Size Distance

18 AWG

16 AWG

Up to 100 ft

Up to 200 ft

Wire Size Distance

24 AWG

22 AWG

Up to 800 ft

Up to 1600 ft

Speaker Adjust

Microphone Adjust

Feedback Adjust

Ferrite

Filter

The 1802 is programmed from the factory with “9 9 9 9” as

the default “Master Code”. It can be re-programmed if desired.

1. Turn Master Code switch ON.

2. Choose and enter a four digit Master Code

number, then press “

”, “beep” will be heard.

3. Turn Master Code switch OFF.

Switch OFF - Normal operating mode positon.

Switch ON - After master code switch has been turned ON, system

will be in Master Code programming mode. (If master code switch

is turned ON and master code is not entered, the system will

sound a short tone after 30 seconds and continue every 30

seconds until master code is entered or switch is turned off).

Master Code Switch Description

Re-Programming the “Master Code”

MASTER CODE

OFF

? ? ? ?

(Write down your master code).

OPER

Set the directory code length to 1 - 2 - 3 or 4 digits.

If 11 or more residents are going to be programmed into the system, the directory code length must be at least two-digits.

If 101 or more residents are going to be programmed in, the directory code length must be at least three-digits.

The factory has already set this for three (3) digits but it can be changed if desired.

Program the Directory Code Length into System

1. Press and enter your four-digit MASTER CODE (beep). Note: Factory setting is “9999”.

2. Enter the directory code digit length (1, 2, 3 or 4), then press (beep).

3. Press (beep) to cancel this function, OR (beeeeeep) to confirm the change.

The programming sequence will automatically end itself after pressing . This CANNOT be UNDONE!

? ? ? ?

OPER

ABC

CAUTION: After programming this sequence, it is NOT recommended changing the directory code length.

Re-programming this sequence in the future will delete ALL phone numbers and directory codes that have

been previously programmed into the system.

OPER

Program the directory codes and 7-digit phone numbers into the system. Be sure you have programmed the directory code

length before programming phone numbers.

Note: Directory code 0, 00, 000, 0000 should be used for management or an emergency phone number. Refer to manual for

more information about this specific directory code.

Program Directory Codes and 7-Digit Phone Numbers into System

? ? ? ?

OPER

Note: If this telephone entry system is being used in an area that requires more or less than 7-digit dialing,

refer to manual for programming.

1. Press and enter your four-digit MASTER CODE (beep). Note: Factory setting is “9999”.

2. Choose and enter a directory code (1, 2, 3 or 4 digits, depending on what was programmed above), then press (beep).

3. Enter a seven-digit phone number for the chosen directory code, then press (beep).

4. Repeat steps 2 and 3 to enter additional directory codes and 7-digit phone numbers.

Note: The back of the manual contains log tables to record all of this information.

5. Press together to end this programming sequence (beeeeeep).

Basic Programming Required

Basic Wiring Required

Basic Adjustments Required

Speaker volume, microphone volume and feedback ALL interact with each other to affect the audio performance of the system.

Locate the speaker volume, microphone volume and feedback adjustments on circuit board.

Place a phone call from

the telephone entry system to a resident using a resident’s directory code.

2. While they are talking, adjust the speaker volume for adequate sound.

3. Talk to the resident in a normal voice to adjust the microphone volume. Ask the resident to let you know when the

sound in their telephone is adequate.

4. After speaker and microphone have been adjusted, ask the resident to remain silent.

5. Remove the jumper from the TONE OFF terminals on the circuit board and place it on the TONE ON terminals. A tone

will be heard in the speaker.

6. Rotate the feedback adjustment. When the tone from the speaker is minimum, this is the correct adjustment.

7. Jumper MUST be moved back to the TONE OFF terminals when complete.

321

MIC VOL

321

SPK

VOL

FEEDBACK

321

Speaker Volume, Microphone and Feedback

TONE

OFF

Tone On/Off Jumper

Note: High microphone and speaker volume levels may cause feedback. It may be necessary to reduce the

speaker volume if the microphone volume is set too high. Likewise, it may be necessary to reduce the

microphone volume if the speaker volume is set too high.

Wire polarity does not matter

It is highly recommended that you consult the Installation/Owner’

s manual for complete instructions on all wiring and programming.

The 1802 needs wiring to an incoming telephone line, power wiring, connection to a entr

y door or gate and it MUST be properly grounded.

The 1802

MUST have DIRECTORY CODES programmed into it to be able to contact the residents from the system. The resident will be able to

GRANT ACCESS

and open the door or gate by pressing “9” on their phone or DENY ACCESS by pressing “#” on their phone.

Relay 1 Strike T

ime Note:

Relay 1 strike time is factor

set for 1 second. Strike time

can be re-programmed from

1/4 second up to 99

seconds. Refer to manual

for re-programming if

desired

LCD Display - Welcome Note: The

welcome message is factory set and

will probably need to be

re-programmed for your specific

needs. Refer to manual for

re-programming welcome message

if desired.

LCD Display - 1802EPD ONLY Note:

The electronic programmable

display should have the resident

names programmed into it after the

directory codes have been

programmed in. Refer to manual for

programming names into the

1802EPD system.

QUICKSTART “BASIC” WIRING AND PROGRAMMING GUIDELINES FOR 1802 AND 1802EPD

1802-066-A-5-14

1 2

Kommentare zu diesen Handbüchern

Keine Kommentare

DoorKing 1802 Bedienungshandbuch Seite 2

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Telefone DoorKing 1802